Your Complete Tutorial for Bathtub Installation
Your Complete Tutorial for Bathtub Installation
Blog Article
This article listed below pertaining to Installing A Bathtub is rather entertaining. Check it out yourself and figure out what you think about it.

Mounting a bathtub isn't specifically rocket science, but it does call for strong plumbing, woodworking, as well as often, tiling skills. Replacing an old bathtub with a brand-new one is likewise a moderately hard task. If the old bathtub is easily accessible, the task can move speedily; if you have to open up a wall surface to eliminate the old bathtub as well as place the new tub, the job is much harder. In either situation, the job is within a home handyman's skills, although you will require a helper to move out the old tub as well as set in the brand-new one. Make certain you have actually qualified yourself for the job and fit trying it. As opposed to employing a specialist to take over a halfway-completed task, it is much better to think about utilizing one prior to you begin. Chances are you might need a specialist plumber to make tube connections.
This article will assist you set up a new bathtub in your shower room if you have actually currently gotten a new bathtub as well as don't require to alter the plan of your previous water pipes.
Your devices and material checklist should consist of the following:
Planning for the Setup
First of all, the supporting structure supplied with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to ensure that if the faucet features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is additionally reasonable to fit a supporting plate under the taps device to stop stress on the bathtub.
Fit the flexible tap adapters to the bottom of both faucets using 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bath. Make certain you utilize every one of the provided washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the water supply. After doing so, turn on the taps to drain any kind of water remaining in the system. The procedure of removing the existing taps can be quite bothersome as a result of the limited gain access to that is commonly the situation.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a cloth prepared for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been eliminated, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming throughout this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will need to be cleaned of any old securing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline links on the old taps to the new taps. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Tub
Utilizing both wooden boards under its feet, place the bathtub in the needed setting. The wooden boards are handy in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four small factors.
The following objective is to make sure that the tub is leveled all round. This can be accomplished by examining the spirit level and also adjusting the feet on the bath tub till the spirit level reviews degree.
To mount taps, fit all-time low of the outermost versatile tap adapter to the suitable supply pipeline by making a compression join; after that do the exact same for the other tap.
Switch on the water supply and inspect all joints as well as new pipework for leaks as well as tighten them if essential. Load the bathtub and additionally check the overflow outlet as well as the typical electrical outlet for leaks.
Ultimately, fix the bathroom paneling as explained in the supplier's instruction manual. Tiling and also securing around the bath tub needs to wait up until the bathtub has actually been made use of a minimum of once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic port to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap and the other end gives a connection to the current supply pipes.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the installing hole in the bath/basin making certain that the washers remain in location between the tap and also the sink. Secure the faucet in place with the producer supplied backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with normal faucet connectors. The previous type needs to be linked to the faucet ends initially, tightening up only by hand. The supply pipelines can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bath satisfies the floor tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can move enough to fracture an inflexible seal, causing the water to pass through the wall surface in between the bathroom and also the tiling, leading to issues with moisture as well as possible leaks to the ceiling listed below.
You can pick from a range of coloured sealers to blend in your fixtures and fittings. They are marketed in tubes as well as cartridges, and are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to load, you can fill it with twists of drenched newspaper or soft rope. Remember to always load the bathtub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can split fairly very early if you do not take into consideration this movement prior to securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were shown that write-up on How to Install a Bathtub from a good friend on another web blog. Appreciated our post? Please share it. Let other people find it. I am grateful for your time. Please pay a visit to our website back soon.
Local favorite for plumbing emergencies. Report this page